Physical Memory Model

Physical memory in a system may be addressed in different ways. The simplest case is when the physical memory starts at address 0 and spans a contiguous range up to the maximal address. It could be, however, that this range contains small holes that are not accessible for the CPU. Then there could be several contiguous ranges at completely distinct addresses. And, don't forget about NUMA, where different memory banks are attached to different CPUs.

Linux abstracts this diversity using one of the three memory models: FLATMEM, DISCONTIGMEM and SPARSEMEM. Each architecture defines what memory models it supports, what the default memory model is and whether it is possible to manually override that default.

注釈

At time of this writing, DISCONTIGMEM is considered deprecated, although it is still in use by several architectures.

All the memory models track the status of physical page frames using struct page arranged in one or more arrays.

Regardless of the selected memory model, there exists one-to-one mapping between the physical page frame number (PFN) and the corresponding struct page.

Each memory model defines pfn_to_page() and page_to_pfn() helpers that allow the conversion from PFN to struct page and vice versa.

FLATMEM

The simplest memory model is FLATMEM. This model is suitable for non-NUMA systems with contiguous, or mostly contiguous, physical memory.

In the FLATMEM memory model, there is a global mem_map array that maps the entire physical memory. For most architectures, the holes have entries in the mem_map array. The struct page objects corresponding to the holes are never fully initialized.

To allocate the mem_map array, architecture specific setup code should call free_area_init_node() function or its convenience wrapper free_area_init(). Yet, the mappings array is not usable until the call to memblock_free_all() that hands all the memory to the page allocator.

If an architecture enables CONFIG_ARCH_HAS_HOLES_MEMORYMODEL option, it may free parts of the mem_map array that do not cover the actual physical pages. In such case, the architecture specific pfn_valid() implementation should take the holes in the mem_map into account.

With FLATMEM, the conversion between a PFN and the struct page is straightforward: PFN - ARCH_PFN_OFFSET is an index to the mem_map array.

The ARCH_PFN_OFFSET defines the first page frame number for systems with physical memory starting at address different from 0.

DISCONTIGMEM

The DISCONTIGMEM model treats the physical memory as a collection of nodes similarly to how Linux NUMA support does. For each node Linux constructs an independent memory management subsystem represented by struct pglist_data (or pg_data_t for short). Among other things, pg_data_t holds the node_mem_map array that maps physical pages belonging to that node. The node_start_pfn field of pg_data_t is the number of the first page frame belonging to that node.

The architecture setup code should call free_area_init_node() for each node in the system to initialize the pg_data_t object and its node_mem_map.

Every node_mem_map behaves exactly as FLATMEM's mem_map - every physical page frame in a node has a struct page entry in the node_mem_map array. When DISCONTIGMEM is enabled, a portion of the flags field of the struct page encodes the node number of the node hosting that page.

The conversion between a PFN and the struct page in the DISCONTIGMEM model became slightly more complex as it has to determine which node hosts the physical page and which pg_data_t object holds the struct page.

Architectures that support DISCONTIGMEM provide pfn_to_nid() to convert PFN to the node number. The opposite conversion helper page_to_nid() is generic as it uses the node number encoded in page->flags.

Once the node number is known, the PFN can be used to index appropriate node_mem_map array to access the struct page and the offset of the struct page from the node_mem_map plus node_start_pfn is the PFN of that page.

SPARSEMEM

SPARSEMEM is the most versatile memory model available in Linux and it is the only memory model that supports several advanced features such as hot-plug and hot-remove of the physical memory, alternative memory maps for non-volatile memory devices and deferred initialization of the memory map for larger systems.

The SPARSEMEM model presents the physical memory as a collection of sections. A section is represented with struct mem_section that contains section_mem_map that is, logically, a pointer to an array of struct pages. However, it is stored with some other magic that aids the sections management. The section size and maximal number of section is specified using SECTION_SIZE_BITS and MAX_PHYSMEM_BITS constants defined by each architecture that supports SPARSEMEM. While MAX_PHYSMEM_BITS is an actual width of a physical address that an architecture supports, the SECTION_SIZE_BITS is an arbitrary value.

The maximal number of sections is denoted NR_MEM_SECTIONS and defined as

NR\_MEM\_SECTIONS = 2 ^ {(MAX\_PHYSMEM\_BITS - SECTION\_SIZE\_BITS)}

The mem_section objects are arranged in a two-dimensional array called mem_sections. The size and placement of this array depend on CONFIG_SPARSEMEM_EXTREME and the maximal possible number of sections:

  • When CONFIG_SPARSEMEM_EXTREME is disabled, the mem_sections array is static and has NR_MEM_SECTIONS rows. Each row holds a single mem_section object.

  • When CONFIG_SPARSEMEM_EXTREME is enabled, the mem_sections array is dynamically allocated. Each row contains PAGE_SIZE worth of mem_section objects and the number of rows is calculated to fit all the memory sections.

The architecture setup code should call memory_present() for each active memory range or use memblocks_present() or sparse_memory_present_with_active_regions() wrappers to initialize the memory sections. Next, the actual memory maps should be set up using sparse_init().

With SPARSEMEM there are two possible ways to convert a PFN to the corresponding struct page - a "classic sparse" and "sparse vmemmap". The selection is made at build time and it is determined by the value of CONFIG_SPARSEMEM_VMEMMAP.

The classic sparse encodes the section number of a page in page->flags and uses high bits of a PFN to access the section that maps that page frame. Inside a section, the PFN is the index to the array of pages.

The sparse vmemmap uses a virtually mapped memory map to optimize pfn_to_page and page_to_pfn operations. There is a global struct page *vmemmap pointer that points to a virtually contiguous array of struct page objects. A PFN is an index to that array and the the offset of the struct page from vmemmap is the PFN of that page.

To use vmemmap, an architecture has to reserve a range of virtual addresses that will map the physical pages containing the memory map and make sure that vmemmap points to that range. In addition, the architecture should implement vmemmap_populate() method that will allocate the physical memory and create page tables for the virtual memory map. If an architecture does not have any special requirements for the vmemmap mappings, it can use default vmemmap_populate_basepages() provided by the generic memory management.

The virtually mapped memory map allows storing struct page objects for persistent memory devices in pre-allocated storage on those devices. This storage is represented with struct vmem_altmap that is eventually passed to vmemmap_populate() through a long chain of function calls. The vmemmap_populate() implementation may use the vmem_altmap along with altmap_alloc_block_buf() helper to allocate memory map on the persistent memory device.