Kernel driver adm1275¶

Supported chips:

Analog Devices ADM1075

Prefix: 'adm1075'

Addresses scanned: -

Datasheet: www.analog.com/static/imported-files/data_sheets/ADM1075.pdf

Analog Devices ADM1272

Prefix: 'adm1272'

Addresses scanned: -

Datasheet: www.analog.com/static/imported-files/data_sheets/ADM1272.pdf

Analog Devices ADM1275

Prefix: 'adm1275'

Addresses scanned: -

Datasheet: www.analog.com/static/imported-files/data_sheets/ADM1275.pdf

Analog Devices ADM1276

Prefix: 'adm1276'

Addresses scanned: -

Datasheet: www.analog.com/static/imported-files/data_sheets/ADM1276.pdf

Analog Devices ADM1278

Prefix: 'adm1278'

Addresses scanned: -

Datasheet: www.analog.com/static/imported-files/data_sheets/ADM1278.pdf

Analog Devices ADM1293/ADM1294

Prefix: 'adm1293', 'adm1294'

Addresses scanned: -

Datasheet: http://www.analog.com/media/en/technical-documentation/data-sheets/ADM1293_1294.pdf

Author: Guenter Roeck <linux@roeck-us.net>

Description¶

This driver supports hardware monitoring for Analog Devices ADM1075, ADM1272, ADM1275, ADM1276, ADM1278, ADM1293, and ADM1294 Hot-Swap Controller and Digital Power Monitors.

ADM1075, ADM1272, ADM1275, ADM1276, ADM1278, ADM1293, and ADM1294 are hot-swap controllers that allow a circuit board to be removed from or inserted into a live backplane. They also feature current and voltage readback via an integrated 12 bit analog-to-digital converter (ADC), accessed using a PMBus interface.

The driver is a client driver to the core PMBus driver. Please see Documentation/hwmon/pmbus.rst for details on PMBus client drivers.

Usage Notes¶

This driver does not auto-detect devices. You will have to instantiate the devices explicitly. Please see Documentation/i2c/instantiating-devices.rst for details.

The ADM1075, unlike many other PMBus devices, does not support internal voltage or current scaling. Reported voltages, currents, and power are raw measurements, and will typically have to be scaled.

The shunt value in micro-ohms can be set via device tree at compile-time. Please refer to the Documentation/devicetree/bindings/hwmon/adm1275.txt for bindings if the device tree is used.

Platform data support¶

The driver supports standard PMBus driver platform data. Please see Documentation/hwmon/pmbus.rst for details.

Sysfs entries¶

The following attributes are supported. Limits are read-write, history reset attributes are write-only, all other attributes are read-only.

inX_label	"vin1" or "vout1" depending on chip variant and configuration. On ADM1075, ADM1293, and ADM1294, vout1 reports the voltage on the VAUX pin.
inX_input	Measured voltage.
inX_min	Minimum Voltage.
inX_max	Maximum voltage.
inX_min_alarm	Voltage low alarm.
inX_max_alarm	Voltage high alarm.
inX_highest	Historical maximum voltage.
inX_reset_history	Write any value to reset history.
curr1_label	"iout1"
curr1_input	Measured current.
curr1_max	Maximum current.
curr1_max_alarm	Current high alarm.
curr1_lcrit	Critical minimum current. Depending on the chip configuration, either curr1_lcrit or curr1_crit is supported, but not both.
curr1_lcrit_alarm	Critical current low alarm.
curr1_crit	Critical maximum current. Depending on the chip configuration, either curr1_lcrit or curr1_crit is supported, but not both.
curr1_crit_alarm	Critical current high alarm.
curr1_highest	Historical maximum current.
curr1_reset_history	Write any value to reset history.
power1_label	"pin1"
power1_input	Input power.
power1_input_lowest	Lowest observed input power. ADM1293 and ADM1294 only.
power1_input_highest	Highest observed input power.
power1_reset_history	Write any value to reset history. Power attributes are supported on ADM1075, ADM1272, ADM1276, ADM1293, and ADM1294.
temp1_input	Chip temperature.
temp1_max	Maximum chip temperature.
temp1_max_alarm	Temperature alarm.
temp1_crit	Critical chip temperature.
temp1_crit_alarm	Critical temperature high alarm.
temp1_highest	Highest observed temperature.
temp1_reset_history	Write any value to reset history. Temperature attributes are supported on ADM1272 and ADM1278.